Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Colorado Springs Homeowners Choose HeatShield Chimney Cleaning
Olympus Chimney Sweep provides independent HeatShield chimney cleaning and resurfacing service in Colorado Springs. HeatShield is a ceramic-based resurfacing system for fireboxes, smoke chambers, and crowns, and we work with it as an independent service provider, not as a dealer and not with any manufacturer authorization. What sets our HeatShield work apart is judgment: we assess whether the masonry behind the coating is sound enough to hold a repair, and we say so plainly when it isn’t. Call (844) 560-6330. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Most general sweep crews brush and vacuum, then hand you a folder of problems to chase down with someone else. HeatShield resurfacing is a specialty repair many of them never install at all. That gap matters in Colorado Springs, where the housing stock asks more of a chimney than most places do.
Why Trust Olympus Chimney Sweep for Your HeatShield Chimney Cleaning?
Our technicians have up to 13 years of experience, and that experience includes HeatShield materials specifically: how the compound behaves when it’s applied over brick that was prepped correctly, and how it behaves when it wasn’t. We work with the HeatShield product line regularly enough to know where it shines and where it fails, and we won’t sell you a coating on masonry that needs real repair first.
We are an independent shop. Olympus Chimney Sweep is not affiliated with, authorized by, or backed by HeatShield. We’re not factory-trained and we’re not a HeatShield dealer. What we are is a chimney company that repairs, installs, and services HeatShield equipment using quality parts that fit it, so the work holds up through a Colorado Springs winter instead of flaking off by spring.
That independence is useful to you. A shop that only sells one product tends to find that product is always the answer. We carry the full lifecycle under one roof, cleaning, inspection, and repair, so a HeatShield question gets an honest diagnostic answer rather than a sales pitch. Our technicians have up to 13 years of experience with the trade-specific realities: flue, liner, crown, damper, smoke shelf, and the way altitude changes what creosote does inside all of them.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common HeatShield Chimney Cleaning Problems We Fix in Colorado Springs
Here’s where HeatShield work goes wrong, and why. These aren’t hypotheticals. They’re the patterns we see when we open a firebox that was resurfaced by someone in a hurry.
- Coating delaminating within a season or two. HeatShield compound applied over a wet, sooty, or poorly prepped firebox doesn’t bond, and it flakes off in sheets. Prep is the entire job. We grind back to sound masonry, clean it properly, and let it dry before any compound touches it.
- Crown coating cracking or lifting. A crown that wasn’t cleaned, scored, and primed before coating gives the compound nothing to grab. Colorado Springs freeze-thaw cycles find that weak seam fast, and a crown coating that lifts lets water straight into the masonry below.
- Resurfacing hiding structural failure. If the firebox has through-cracks, spalled brick, or a failed crown behind the coating, HeatShield only masks the problem. A coating over a failing structure looks tidy and does nothing. That’s a rebuild or repointing job, and we’ll tell you so before you pay for a resurfacing.
- Smoke chamber work that ignores throat geometry. When resurfacing doesn’t follow the original throat shape, the flue short-circuits and smoke rolls out into the room instead of up the chimney. The coating can be flawless and the fireplace still smokes. Geometry comes first.
- Altitude-driven deterioration at the crown and firebox. Colorado Springs sits above 6,000 feet, and intense UV plus repeated freeze-thaw cracks mortar and crown surfaces faster here than at lower elevations. Thinner air also changes how wood burns and how the chimney drafts, which affects how creosote accumulates and where moisture sits.
A typical HeatShield job starts with a homeowner noticing whitish powder and hairline crazing across the firebox floor and rear wall. A sweep then finds HeatShield applied years earlier over a firebox that was never properly cleaned, coating lifting in sheets. After a Level 2 inspection confirms the brick behind it is still sound, the pro grinds off the failed material, preps the masonry, and reapplies genuine HeatShield compound at the correct thickness. If the inspection instead shows spalling brick or a cracked crown, the scope shifts to masonry repair before any coating goes on. A separate common call is a crown coating that cracked through in a single season because it went on without cleaning and scoring. The fix there is proper crown repair or recasting, not another layer of coating. Found during inspection, fixed on the same call.
HeatShield Parts & Our Repair-vs-Replace Approach
For resurfacing, we use genuine HeatShield compound. Aftermarket firebox mixes and generic refractory cements don’t match its adhesion and heat properties, so a cheaper compound is a false economy that shows up as a failed coating a couple of winters down the road. We don’t claim to stock or carry OEM HeatShield parts as a distributor; we source the correct material for the job in front of us.
The repair-or-replace decision comes down to what the masonry is doing behind the surface. HeatShield is the right call for sound masonry with surface deterioration: a firebox that’s crazed, chalky, or worn but structurally intact. It’s the wrong call when there are through-cracks, spalled wythes, or a failed crown. Those need real masonry work, repointing or rebuilding, before any coating goes on. We’d rather tell you that up front than coat a failing firebox and collect the check.
If you’re unsure which category your fireplace falls into, that’s exactly the question an inspection answers. Call (844) 560-6330 and estimates are free.
Our HeatShield Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection where the situation calls for it: firebox, smoke chamber, throat geometry, crown, and flue. We’re looking for what’s surface wear and what’s structural, because that distinction decides everything that follows.
- 2
Repair or installation. If the masonry is sound, we grind off any failed coating, clean and prep the surface, and apply genuine HeatShield compound to the correct thickness for the firebox, smoke chamber, or crown. If the masonry isn’t sound, the scope changes to structural repair first.
- 3
Test. We check the repair for coverage, thickness, and adhesion, and we test draft to confirm smoke goes up the flue rather than into the room. A crown gets checked for proper slope and seal at the flue.
- 4
Documentation. You get a clear record of what was found, what was done, and what to watch over the next few seasons. That record matters in Colorado Springs, where insurers sometimes ask for documented chimney inspections after wildfire events.
See the difference
Before
After
Before
After
Before
AfterHeatShield Products We Service & Install in Colorado Springs
We service and install the core HeatShield line: FireGuard firebox resurfacing compound, CrownSeal and CrownCoat crown repair compounds, SmokeChamber and smoke shelf resurfacing mix, and the damper and pumice repair products. Each one has a specific job and a specific set of conditions where it works. FireGuard is for sound firebox masonry with surface deterioration. CrownSeal and CrownCoat are for crown surfaces that are intact but weathered, not for crowns that are structurally cracked. The smoke chamber mix restores a surface that’s rough or deteriorated while preserving the throat shape the fireplace was built around. Damper and pumice products address worn damper components and pitted firebox surfaces. Getting the material matched to the condition is most of the work.
We Also Service These Brands
HeatShield is one piece of a full repair scope. We also work with DuraFlex flexible liner systems for damaged or non-compliant flues, and Gelco caps for the top end of the chimney where weather gets in. That range means a problem found during a HeatShield job doesn’t turn into a referral to another contractor. Cleaning, inspection, and repair stay with one company, which is the whole point of hiring a repair-capable chimney specialist in Colorado Springs.
FAQs – HeatShield Chimney Cleaning Service in Colorado Springs
No. HeatShield is a ceramic-based resurfacing compound formulated for firebox, smoke chamber, and crown surfaces, and it’s applied in layers to a specific thickness over properly prepped masonry. Paint is cosmetic. HeatShield is a repair material, and it only performs like one when the prep and thickness are right. A thin coat slapped over soot is neither.
Not successfully. A new layer over a delaminating one will fail the same way, usually faster. The failed material has to be ground off, the masonry cleaned and dried, and the surface prepped before fresh compound goes on. If the brick behind the old coating is spalled or cracked, the coating isn’t the right repair at all. Call (844) 560-6330 for an assessment. Estimates are free.
It depends on whether the crown is structurally sound. Surface weathering, minor pitting, and a worn top layer without through-cracks are candidates for crown coating. A crown with structural cracks, separation from the flue, or a failed slope needs repair or recasting, because a coating over a broken crown just hides the water path. An inspection settles it.
Only if the smoke problem is caused by a deteriorated smoke chamber surface or poor throat geometry that the resurfacing correctly restores. If smoke roll-out comes from a flue that’s too short, a blockage, or a draft problem elsewhere, resurfacing won’t fix it and shouldn’t be sold as though it will. Draft diagnosis comes before repair. Call (844) 560-6330 to book an inspection. Estimates are free.
We can’t speak to HeatShield’s warranty terms, because we’re an independent service provider and not affiliated with or authorized by HeatShield. What we can tell you is that we use genuine HeatShield compound for resurfacing and follow proper prep and application practice, which is what any manufacturer warranty depends on anyway. Ask us directly about the terms on your specific job when we write the estimate.
HeatShield work is priced per job by a written estimate, not by a flat rate, because a firebox resurfacing and a crown coating are different scopes and the condition of the masonry changes the labor. Cleaning and inspection are quoted separately from resurfacing so you can see exactly what you’re paying for. Estimates are free. Call (844) 560-6330 for an exact quote.
Book Your HeatShield Service in Colorado Springs, CO
If your firebox is crazing, your crown coating is lifting, or you’re not sure whether the masonry behind a failed resurfacing is sound, we’ll tell you straight. Call (844) 560-6330 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Olympus Chimney Sweep.