Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Inspection for Colorado Springs Homeowners
Most flue problems in Colorado Springs announce themselves the wrong way: a faint draft that never quite goes away, a stain on the ceiling near the chase, or a fire that burns lazy and smokes at the damper. By the time a problem is obvious, the fix is usually structural, not cosmetic. A proper inspection finds it early, on camera, with photo evidence you can see for yourself.
Olympus Chimney Sweep is built for that. Our technicians have up to 13 years of experience, we work with professional-grade product lines like HeatShield and DuraFlex, and when we find a defect during inspection we can address it on the same call instead of sending you to another contractor. Same-day appointments are often available in Colorado Springs. Call (844) 560-6330 to book a diagnostic inspection.
Fireplace Inspection
Fireplace Inspection is the diagnostic pass that tells you whether your fireplace opening, firebox, damper, and smoke chamber are safe to use. You need one when you buy a home, when you switch fuels, or when the fireplace smokes into the room despite a clean flue. Olympus Chimney Sweep performs a top-to-bottom assessment scoped to the fireplace itself, not just the chimney stack. A typical fireplace inspection runs $99-$250 depending on how much of the assembly needs to be opened up or imaged. The written estimate sets the final price before any work begins.
Firebox and Damper Condition
We check the firebox for cracked firebrick, spalled mortar joints, and gaps in the refractory panels that could let heat reach framing. The damper is tested for a full open and close, then inspected for warping or a burned-out hinge. Both fail slowly and quietly before they fail dangerously.
Smoke Chamber and Draft Path
A smoke chamber with rough, offset surfaces collects creosote and stalls the draft. We look at the transition from the firebox into the smoke chamber and the damper shelf above it, because that’s where fireplace smoke problems usually start. Smooth the path and the fire pulls correctly again.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Inspection Services
Chimney Inspection Services cover the full system: crown, flashing, masonry stack, flue, cap, damper, and appliance connection, evaluated as one assembly. You need them before you buy a Colorado Springs home, after a chimney fire, after severe wind, or as a routine annual evaluation before burning season. Olympus Chimney Sweep offers three tiers of inspection matched to what you’re asking us to find. Camera-based and structural inspections in Colorado Springs typically run $150-$450 depending on the level and access. The written estimate is the final word on price.
Roof-Level and Exterior Review
From the roof, we inspect the crown for cracks, the flashing for lifted or missing seals, and the cap for damage that lets water or animals in. We photograph what we see, so you can judge the extent for yourself. Nothing is recommended without camera evidence.

Interior Components and Appliance Connection
Inside, we check the firebox, damper, and the connection between the appliance and the flue for gaps or improper fit. That joint is where carbon monoxide risk is highest when it’s wrong. We flag it plainly, and we fix it on the same visit if you approve.

Chimney Flue Inspection
Chimney Flue Inspection is the focused evaluation of the flue itself: its size, its liner integrity, and whether the gases it vents are leaving the way they should. You need one when you have a masonry chimney with no liner, when you’ve switched to a high-efficiency appliance, or when the draft has become unreliable. Olympus Chimney Sweep images the full run of the flue so we can confirm what’s actually inside before recommending a repair. A flue-only inspection runs $99-$200 in Colorado Springs, with a written estimate setting the final price.
Flue Sizing and Draft
An undersized flue won’t pull correctly, and no amount of sweeping fixes that. We measure the flue’s cross-section against the appliance’s output to confirm the sizing is right for the job. If it’s not, we can discuss relining with DuraFlex as a permanent solution.
Liner Integrity
Clay tile liners crack; that’s normal wear, not a defect you caused. The question is whether the crack has opened a path to framing or to another flue in the same stack. We check the tile joints all the way up, and we can resurface a worn masonry flue with HeatShield when that’s the correct fix rather than a rebuild.
Chimney Fire
Chimney Fire is not an event you can see and forget; the real risk is what it leaves behind. A fire in the flue can crack tile liners, warp dampers, and turn creosote into a hard glaze that a brush won’t remove, so the chimney should be inspected before the next fire. You need an inspection after any chimney fire even if the fire seemed small and the flue looks intact. Olympus Chimney Sweep inspects post-fire damage and can address what’s found with HeatShield resurfacing or DuraFlex relining. Post-fire inspections in Colorado Springs run $150-$350 depending on what needs imaging. The written estimate sets the final price.
Creosote Glaze and Its Consequences
Stage 3 creosote is hard, tar-like, and highly combustible; it’s what fuels the most severe chimney fires. Brushing alone won’t remove it, so we inspect for glaze and recommend a chemical or rotary cleaning method when it’s present. This is a job for a trained technician, not a homeowner.
Structural Damage After a Burn
A fire hot enough to glaze the liner is hot enough to crack it. We image the flue to check for tile separation, spalling, and heat damage to the smoke chamber, because the visible surface can look fine while the structure behind it is compromised. That’s exactly the kind of defect that justifies a full inspection.
Level 2 Chimney Inspection
Level 2 Chimney Inspection is the scope required at a real estate transaction and after any event that could have damaged the chimney, including fire, earthquake, or severe weather. It goes beyond a visual check, using cameras on the flue and a full examination of accessible interior and exterior components. Olympus Chimney Sweep performs Level 2 inspections with photographic documentation so the findings travel with the report. A Level 2 inspection in Colorado Springs typically runs $150-$450 depending on roof access and how much of the flue needs imaging. Call (844) 560-6330 to schedule; estimates are free and the written price is final before we begin.
Real Estate and Change-of-Ownership Work
Buyers and sellers need a documented condition of the chimney before closing, and lenders or insurers often ask for it. We produce a written report with photographs that hold up in a transaction. Any finding that needs repair is spelled out with an estimate, not just a note.
What the Camera Catches That the Eye Doesn’t
From the top of the stack, you can see maybe three feet down the flue. The camera goes the whole way, catching offset tile joints, missing mortar, a bird’s nest, a broken damper, or a disconnected liner that a top-down visual would miss entirely. That’s where the value of a Level 2 inspection lives.
Chimney Leak
Chimney Leak is what happens when the chase isn’t watertight, and the symptoms usually show up indoors as a ceiling stain, a rusted damper, or loose brick near the roofline. You need a leak inspection when water is finding its way in, not a coat of paint over the symptom. Olympus Chimney Sweep traces the source: crown cracks, failed flashing, a missing or damaged Gelco cap, or porous brick that needs sealing. Leak diagnosis in Colorado Springs runs $150-$350 depending on the access and imaging required. The written estimate sets the final price.
Flashing, Crown, and Cap Failures
Most leaks start at the flashing joint where the chimney meets the roof, because caulk and sealant dry out and lift over time. The crown cracks next, letting water seep between masonry and flue. A properly seated Gelco cap closes the top of the chimney and keeps rain, snow, and animals out while still venting.
Tracing Water to Its Source
Water rarely enters where the stain appears; it travels down the flue wall or through the masonry before showing up. We don’t guess, we inspect the stack, the flashing, and the cap separately to confirm the source. If work can safely wait, we tell you so, rather than selling a full rebuild you don’t need.
Chimney Camera Inspection
Chimney Camera Inspection is the video pass inside the flue that turns a guess into a diagnosis. You need one whenever the flue’s condition isn’t visible from the top, when a sweep finds something unusual, or when a prior repair needs verifying. Olympus Chimney Sweep runs the camera the full length of the flue, so the images we base recommendations on are the ones you get to see. A camera-based inspection in Colorado Springs runs $150-$350 depending on access and how far the flue reaches. Call (844) 560-6330 to schedule; estimates are free.
How the Camera Works
We lower a self-lit, articulated camera down the flue and record the run in real time, with a monitor that lets you watch along. The camera shows tile joints, mortar, cracks, offset sections, and connections that a top-down view misses. You get to see the defect before anyone recommends a repair.
What We Capture in the Report
The report includes stills of each finding, the camera position, and a plain-language description of what it means for your chimney. If repairs are needed, we list them with a written estimate. If they can wait, we say so.
Brands We Service
We work with the product lines that professional chimney technicians rely on, and we know where each one wears out. HeatShield resurfacing material is what we use when a masonry flue needs restoration without a full rebuild, and it holds up where a thin patch would fail. DuraFlex flexible liners let us reline a damaged or undersized flue with a permanent solution. When a leak is the issue, a properly fitted Gelco cap closes the top of the stack and keeps water and animals out.
We also work with Olympia Chimney components and Famco venting hardware for installations and repairs that call for them. Whether you have HeatShield resurfacing, DuraFlex liner, or any other manufacturer’s product already on your chimney, we can help assess it and repair it correctly. Call (844) 560-6330 for a free estimate.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Stains on the ceiling or wall near the chase. Water finding its way through flashing or a cracked crown shows up indoors first. A small stain usually means the leak has been working through the masonry for a while.
- A fire that smokes back into the room. A closed or stuck damper, an undersized flue, or a blocked flue can each cause it, and the cause needs to be found before the next fire is lit. Don’t guess, inspect.
- Creosote flaking off the flue or glaze visible inside. Stage 3 glaze is combustible and won’t come off with a brush. It’s the leading fuel for a chimney fire and should be addressed by a trained technician.
- A fire has already happened in the flue. Even a small chimney fire can crack a tile liner or warp a damper. Inspect before the next fire, not after.
- It’s been more than a year since the last inspection. An annual inspection catches liner wear, crown cracks, and flashing gaps early, when repair is cheaper and simpler.
Our Process, Step by Step
- 1
Book and confirm scope. We ask what you’ve noticed and match the inspection level to the question, so we’re not running an unnecessary scope. The estimate is written before we start.
- 2
Exterior and roof-level review. We inspect the crown, flashing, cap, and masonry stack from the roof, photographing what we find. Roof and flashing issues often explain indoor leaks.
- 3
Interior inspection. We check the firebox, damper, smoke chamber, and appliance connection against the flue. This is where carbon monoxide risk and draft problems usually originate.
- 4
Camera pass inside the flue. We run the camera the full length of the flue to catch tile separation, offset joints, and missing mortar. You see the images as we record them.
- 5
Written report and estimate. We give you a plain-language summary of the findings, stills from the camera, and an itemized estimate for anything that needs repair. Nothing is recommended without camera evidence you can see.
How Much Does Chimney Inspection Cost in Colorado Springs?
Inspection costs in Colorado Springs are driven by the scope and by how much of the flue needs to be imaged on camera. A typical basic inspection runs $99-$200 depending on access and whether the flue needs a camera pass. A Level 2 inspection, which is what real estate transactions and post-fire evaluations usually require, typically runs $150-$450 depending on roof access, the length of the flue run, and how many components need to be photographed. Leak diagnosis and full structural evaluations usually land in the $150-$350 range.
What moves the price: roof pitch and access, how many flues are in the stack, whether a prior repair needs verifying, and whether the appliance connection is difficult to reach. What doesn’t move the price: whether you call for a same-day slot or schedule later in the week. Our price is set per job by the written estimate, not by the calendar.
The free-estimate side of the equation matters more than people expect. When you know the scope up front, you avoid being told after the fact that a liner or masonry repair is needed without an image to back it up. That’s the real overpay: paying for work that wasn’t justified by evidence. We show the stills from the camera before quoting, so you can make the call yourself. If a repair can wait, we tell you so, and we’d rather tell you that than sell you a rebuild you don’t need.
Our Service Area Near Colorado Springs
We schedule inspections across the Colorado Springs metro, including nearby communities like Cimarron Hills and Stratmoor, plus Manitou Springs, Security-Widefield, Fountain, Fort Carson, and the Air Force Academy area. We also cover north-side communities such as Gleneagle, Monument, Woodmoor, and Black Forest. Response times depend on your location and the schedule, so call (844) 560-6330 and we’ll confirm an appointment window. Fast dispatch from 7am to 7pm, Sunday through Friday.
Serving Colorado Springs, CO – Our Local Coverage Area
We serve Colorado Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Inspection in Colorado Springs
A chimney inspection is a professional evaluation of the full venting system, including the flue, crown, flashing, cap, damper, firebox, and appliance connection. It’s diagnostic, not just visual: we assess liner integrity, draft, and structural condition and document findings with camera images. Any repair that comes out of it is quoted with a written estimate before work begins. Call (844) 560-6330 for an exact quote on your inspection.
Most inspections take between 45 minutes and two hours depending on scope. A focused flue-only check is on the shorter end; a Level 2 with a full camera pass and photographic report runs longer. The time depends on roof access, the number of flues, and whether any surprises turn up on camera. Call (844) 560-6330 to book a slot; estimates are free.
Inspection costs typically run $99-$450 depending on the level of scope. A basic inspection usually sits at $99-$200, a Level 2 the real estate or post-fire scope usually requires runs $150-$450, and leak diagnosis lands around $150-$350. The written estimate sets the final price before we start. Call (844) 560-6330 for an exact quote on your inspection.
Yes, we work with HeatShield resurfacing and DuraFlex flexible liner installation as part of our repair scope. If your chimney already has either system installed and you need it verified or evaluated, we can inspect it and recommend the right repair if anything is wrong. Whether you have HeatShield, DuraFlex, or any other manufacturer’s product, we can help. Call (844) 560-6330 for a free estimate.
Same-day appointments are often available in Colorado Springs depending on the schedule. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday, with Saturday closed. A call outside dispatch hours is booked into the next opening. Call (844) 560-6330 to check the schedule.
Warranty coverage depends on the specific repair, and we spell it out in writing on the estimate before any work begins. Inspections themselves don’t carry a warranty because they’re diagnostic; the report is the deliverable. Any repair we do carries its own terms, written down so there’s no ambiguity. Call (844) 560-6330 to talk through the scope.
Clear the area in front of the fireplace and make sure the damper is accessible so the technician can open and close it during the check. Don’t burn anything in the 24 hours before the visit, so the flue is cool and clear to inspect. Have any prior reports or repair records handy for context. Call (844) 560-6330 with any questions before the appointment.
Schedule Your Chimney Inspection Service in Colorado Springs Today
If it’s been a year or more since the last inspection, or if you’ve noticed a stain, a smoking fireplace, or a draft that won’t go away, schedule an inspection now and let a trained technician see what’s actually there. We answer 24/7, fast dispatch runs 7am to 7pm Sunday through Friday, and the estimate is free. Call (844) 560-6330 to book your chimney inspection in Colorado Springs.
Written by the team at Olympus Chimney Sweep.