Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Company in Fountain, CO
Chimney inspection is where most Fountain chimney work starts. Homes here sit on wind-scoured high plains just south of Colorado Springs, and the constant blowing grit plus a real reliance on wood heat during cold snaps means caps, spark arrestors and flues take a beating that a flat visual check will miss. We assess structural integrity and venting performance rather than simply glancing up the flue, so a small issue found now doesn’t become a liner replacement later. Call (844) 560-6330 for a free estimate.
Why Fountain Homes Are Different
Fountain has two chimney populations living side by side. The older single-story ranches from the mid-century through the 1970s and 80s were built around masonry fireplaces that have seen decades of burning and, in many cases, decades of deferred attention. Then there’s the wave of 2000s and 2010s subdivision builds, most of which went in with factory-built fireplaces or wood stoves instead of traditional masonry chimneys. Those units are often clean because they’ve never been properly swept, and the homeowner assumes new means fine.
The climate pushes hard on both. Cold winters with hard freezes work on masonry through repeated freeze-thaw cycles, opening hairline cracks in crowns and mortar joints that water then finds. Persistent wind drives prairie dust and debris straight into caps and spark arrestors, and on windy days along the open east-side lots, grit and even bird nests pack in tight. That’s why we check caps and spark arrestors before we ever look up the flue. Heavy seasonal use then lays creosote on top of all of it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Main Fountain Services
Two jobs account for most of the calls we get across Fountain: cleaning a flue that’s loaded with creosote and debris, and repairing the liner, crown or cap damage that the cleaning turns up.
Chimney Sweep in Fountain
A sweep here is never just a brush and a vacuum. Wind-driven grit often sits on top of the creosote, and in the older ranches around Fountain that grit has had years to work into mortar joints and cap seams. We sweep the flue, then clear the firebox, smoke chamber and damper, and we check the cap and spark arrestor while we’re on the roof. Factory-built units in the newer subdivisions need the same attention, and many of them have gone years without it. Work with Chimney Sweep in Fountain and a problem found during the sweep gets flagged on the spot, not left for a second visit.

Chimney Repair in Fountain
Repair is where freeze-thaw damage shows up. A crown that’s cracked lets meltwater in, and one hard freeze can split it wider. On the older Fountain ranch homes we see mortar joints that have gone soft and flue tiles that cracked from years of heating and cooling. Newer factory-built systems fail differently, usually at the cap or where a wind-damaged spark arrestor has stopped doing its job. We handle Chimney Repair in Fountain with materials built for the work, including HeatShield resurfacing for flues that are pitted or cracked but still structurally sound, and DuraFlex liners when a flue has to be relined.

Chimney Inspection in Fountain
An inspection at altitude here has a different job than in a damp, low-elevation climate. Fountain’s hard freezes and persistent wind mean a chimney can look sound from the ground while the crown, cap or flue lining has already started to fail, and factory-built fireplaces in the newer subdivisions are often never inspected at all after installation. That’s the gap a proper Chimney Inspection closes: we look at the whole venting system, not just the inside of the flue, and record what we find so you can see it yourself.
Fireplace Inspection
Signs you need it
A smoky fire that won’t draft well, a damper that sticks, visible cracks in the firebox brickwork, or a fireplace you’ve never had looked at since moving in.
What it costs in Fountain
A fireplace inspection in Fountain typically runs $89 – $150, with the written estimate setting the final price.
How we do it
We inspect the firebox, damper, smoke chamber and firebox-to-flue transition, check clearances to combustible framing, and photograph what we find.
Chimney Flue Inspection
Signs you need it
Heavy creosote buildup, a flue that smokes back into the room, or a factory-built fireplace that’s past the point where a routine sweep is enough.
What it costs in Fountain
Flue inspection in Fountain is typically $99 – $175, and the written estimate sets the final price.
How we do it
We run a camera up the flue to look for cracked or offset tiles, gaps at joints, warped liners and creosote glazing, then record the interior so you can review the footage.
What Chimney Inspection Costs in Fountain
| Item | Typical range in Fountain |
|---|---|
| Fireplace inspection | $89 – $150 |
| Flue inspection | $99 – $175 |
| Level 2 inspection | $150 – $275 |
Does a chimney in Fountain need a Level 2 inspection after a new install?
Yes. A Level 2 inspection is the standard check after a new appliance goes in, after a chimney changes hands with a property sale, or after any event that may have damaged the flue. It goes further than a basic visual pass. Call (844) 560-6330 for an exact quote, and estimates are free.
Can you inspect a factory-built fireplace in a newer Fountain subdivision?
We do this regularly in the 2000s and 2010s homes across Fountain. Factory-built fireplaces have manufacturer-specific venting and clearance requirements, so the inspection follows the unit’s own specs rather than masonry rules. Problems surface at the cap, the vent sections and the firebox lining. Call (844) 560-6330 for an exact quote; estimates are free.
Brands We Service in Fountain
Fountain systems come in from a range of makers, and we work with professional-grade parts from HeatShield, Gelco, Olympia Chimney and Famco so repairs aren’t held up by a mismatched component. We don’t stock parts locally, so turnaround depends on what the inspection calls for and what we have to order. See our brands for the full picture.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Company in Fountain, CO
| Service | Typical range in Fountain |
|---|---|
| Fireplace inspection | $89 – $150 |
| Flue inspection | $99 – $175 |
| Level 2 inspection | $150 – $275 |
What pushes price up in Fountain is mostly access and condition: a steep roof pitch on a newer subdivision home, a cap packed with wind-driven grit that has to be cleared before the flue can be inspected, or a flue that needs camera work to reach the problem. We give you the price in writing upfront, before any work begins, and the written estimate sets the final figure.
Neighborhoods We Serve in Fountain
We handle chimney work across Fountain’s mix of old ranches and newer subdivisions, and our technicians have up to 13 years of experience reading both. Wherever your home sits relative to the open east-side lots and the prevailing wind, we’ll get to it. Because Fountain is compact, response across the city is quick, and a call outside dispatch hours gets booked into the next opening.
- Countryside
- Cross Creek
- Fountain Valley
- Heritage
- Mesa Ridge
Service Area – Cities Near Fountain
Fountain sits in a cluster of communities south of Colorado Springs, and we work the whole cluster, not just the city limits. That includes Fort Carson, CO to the west, Security-Widefield, CO to the north, Stratmoor, CO toward the interstate, and Colorado Springs, CO itself. If you’re near the line between Fountain and any of these, we can still get to you.
Serving Fountain, CO – Our Local Coverage Area
We serve Fountain and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Chimney Company in Fountain
Fountain is a short run from our Colorado Springs service base, so we can usually reach most of the city quickly. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday; we’re closed on Saturday. Call (844) 560-6330 for a free estimate.
An inspection itself doesn’t require a permit. A repair that alters the flue or the chimney structure often does, and it depends on how your home was built and whether your subdivision’s HOA has rules on visible exterior changes. Ask your city’s building department and your HOA before work begins.
Nothing gets recommended without camera evidence you can see for yourself. We show you the footage, explain what the problem is and what it will take to fix it, and tell you plainly when work can safely wait. Call (844) 560-6330 for a free estimate.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Fountain Customers Say
"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."
- Danika Whitfield"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."
- Carrie Norris"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
- Ruben Rodriguez