Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Colorado Springs Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning, inspection and repair in Colorado Springs. Gelco stainless liners, caps and component kits are documented, spec-driven products, so we can size, inspect and service them against published clearances and ratings rather than guesswork. We’re not affiliated with or authorized by Gelco: our recommendations come from what your flue and appliance actually need. At over 6,000 feet on the shoulder of Pikes Peak, that difference shows up fast, because thin air changes how your fire burns and how creosote collects.
Our technicians have up to 13 years of experience, and we work on Gelco-equipped chimneys every week in Colorado Springs. Call (844) 560-6330. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Olympus Chimney Sweep for Your Gelco Chimney Cleaning?
Gelco hardware rewards a technician who understands how the parts fit together. A Gelco stainless cap, a flexible relining kit, a top-sealing damper: each one has published dimensions and clearances, and each fails in a predictable way when it’s neglected. We read those specs. We measure the flue. And we service the assembly with quality parts that fit the equipment rather than forcing a generic replacement into a collar that was never cut for it.
That matters for your warranty. Gelco’s terms are set by Gelco, not by us, and we won’t pretend otherwise. What we can do is keep the work warranty-safe: correct part dimensions, correct clearances, correct installation practice, and no improvised fixes that put the assembly outside the manufacturer’s published spec. We’re an independent provider, so when we tell you a cap needs replacing or a liner is still sound, we’re reading the hardware and the flue, not a sales script.
Our full-service scope matters here too. We clean, inspect and repair, which means a Gelco problem found during a sweep is a problem we can address on the same visit. No second contractor. No gap between the diagnosis and the fix. Colorado Springs homeowners tell us this is the part they value most.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Colorado Springs
Gelco components fail in recognizable ways. Here’s what we find most often in Colorado Springs, and why each one happens.
- Cap screens and louvers clogged with creosote and debris, then corroding at the seams and fasteners. A stainless cap screen does its job until it packs solid. At altitude, creosote accumulates faster and with a different texture than at lower elevations, and a clogged screen restricts draft. Once airflow drops, moisture lingers, and the seams and fasteners are the first places corrosion gets a foothold. The dry, windy Colorado Springs spring and summer hail both speed that along.
- Flexible liner sections developing creosote glaze at the offset and terminal connections. This is usually a sizing problem, not a sweeping problem. When a flexible liner is sized to the flue rather than the appliance, the gas velocity through the offset is too low to carry creosote out, and it glazes right at the bend. The terminal connection at the top plate collects the same way. A proper Level 2 camera inspection shows this clearly.
- Top-sealing damper gaskets and cables binding or failing, so the flue no longer seals shut. The gasket on a top-sealing damper is a wear part. Freeze-thaw cycles up here work on it the way they work on masonry, and the cable mechanism can bind from grit and creosote dust. When it fails, you lose heat up the flue between burns. A damper that no longer closes flush is a repair, not a reason to stop using the fireplace.
- Liner-to-cap collars and top plates loosening, letting water track down the outside of the liner and stain the firebox. Hail, high winds and thermal movement all work on the fasteners. Once the top plate lifts, water runs between the liner and the flue. The stain on the firebox is the first sign, and by then it’s been happening for a while. This one is worth catching early.
- Factory-built and masonry systems needing different protocols under the same Gelco hardware. Many Colorado Springs homes in Old Colorado City and the Near North End have early-1900s to mid-century masonry fireplaces with clay tile flues that crack from freeze-thaw, while 1990s and 2000s subdivisions north and east often have factory-built metal fireplaces. The cleaning tools, inspection method and creosote expectations differ. We adjust, and we don’t assume the hardware tells us everything about the flue behind it.
Gelco Parts & Our Repair-vs-Replace Approach
Genuine Gelco components are the right call for caps, top plates and liner connectors. Aftermarket caps often don’t match the collar dimensions, and a cap that doesn’t seat correctly is a leak waiting to happen. Where generic liner sections meet the same diameter and UL listing exactly, they’re acceptable. Where they don’t, we won’t use them.
On repair versus replace: if a Gelco liner is sound and only the cap, damper or top plate has failed, replacing those parts is almost always cheaper and better than a full reline. We verify the liner’s condition with a Level 2 camera inspection before recommending either path. A damaged liner that’s still structurally sound with a failing cap gets a cap. A liner with cracked glaze and compromised connections gets a reline. We tell you which, and we show you the footage.
Call (844) 560-6330 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 camera inspection of the liner, the top plate, the cap and the damper. You see the footage. That’s the foundation of everything that follows.
- 2
Repair or install. If it’s a cap, damper or top plate, we replace with a quality part that matches the collar and spec. If it’s a liner issue, we install a liner sized to the appliance, not the flue.
- 3
Test. We re-check draft, confirm the damper seals flush, verify the top plate is seated, and make sure the assembly works in the real Colorado Springs conditions it faces.
- 4
Warranty. We document what was done, what parts were used, and what the manufacturer’s terms cover. You get a record you can hand to an insurer.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Colorado Springs
We service and install Gelco rigid stainless liner sections and tee kits, Gelco flexible stainless relining kits, Gelco multi-flue and single-flue stainless caps, and Gelco top-sealing damper assemblies. That covers the hardware most Colorado Springs owners are dealing with when they call. We don’t claim to stock Gelco parts, and we’re not a Gelco dealer. We work with quality parts that fit the equipment correctly. If you’re unsure what’s on your chimney, a Level 2 inspection tells you before you spend anything on parts.
We Also Service These Brands
Gelco isn’t the only hardware we know. We also work on DuraFlex liner systems and HeatShield chimney resurfacing, and we service the full range of chimney components across both. If your chimney has Gelco hardware up top and a DuraFlex liner or HeatShield-treated flue behind it, one visit covers all of it. Call (844) 560-6330 to book.
FAQs – Gelco Chimney Cleaning Service in Colorado Springs
No. We’re an independent service provider and have no manufacturer authorization or affiliation with Gelco. Our recommendations are based on the flue and appliance, not on a manufacturer relationship. We work on Gelco-equipped chimneys because we know the hardware, not because Gelco sent us.
Yes. We use quality parts that fit Gelco equipment, including genuine Gelco components for caps, top plates and liner connectors where the match matters. We don’t stock or carry OEM parts, and we’re not a dealer. We source the right part for the assembly. Call (844) 560-6330 for a free estimate.
An annual sweep with a Level 2 inspection typically runs a couple of hours. A cap replacement or damper repair adds time but is usually completed on the same visit. A reline is a longer job, scheduled after the inspection findings. We confirm the scope when we book.
Rigid stainless liner sections and tee kits, flexible stainless relining kits, multi-flue and single-flue stainless caps, and top-sealing damper assemblies. That’s the full Gelco chimney hardware range we service and install.
Not when the work respects the manufacturer’s published clearances and dimensions. Gelco sets its own warranty terms, and we keep the work within spec so the assembly stays warranty-safe. We’re independent, so we can’t rule on a Gelco claim, but we can make sure the install doesn’t create one.
It depends on the job: a standard sweep, a cap replacement and a reline are very different scopes. We give you a written estimate per job, free, before any work starts. Call (844) 560-6330 for an exact quote. Estimates are free.
Book Your Gelco Service in Colorado Springs, CO
If your chimney has Gelco hardware, it deserves a technician who knows how that hardware fails and why. We clean, inspect and repair, all in one visit, with no referral gaps. Call (844) 560-6330 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Olympus Chimney Sweep.