Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Colorado Springs Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning and service in Colorado Springs. DuraFlex is a flexible stainless steel chimney liner, and the liner is the part of your chimney that carries smoke, moisture, and heat out of the house, so it sets how well the whole system vents. Our DuraFlex work differs from a basic brush-and-vacuum sweep because we diagnose the liner itself.
We’re an independent service provider. Olympus Chimney Sweep is not affiliated with, authorized by, or endorsed by DuraFlex, and we don’t claim to be. Our familiarity with these liners comes from field experience with the failure points owners actually run into, not from a manufacturer badge. When we open a DuraFlex chimney in Colorado Springs, we’re looking for the same things a trained technician looks for anywhere: creosote where it shouldn’t sit, joints that have moved, and water getting in at the top. Call (844) 560-6330 to book a DuraFlex sweep or inspection.
Key takeaways:
- We service, repair, and install DuraFlex flexible stainless liners as an independent shop.
- We clean with the tools a liner actually needs, not a generic flue brush.
- We use quality parts that fit DuraFlex equipment and protect your warranty position.
- A liner problem found during inspection can be handled on the same visit.
Why Trust Olympus Chimney Sweep for Your DuraFlex Chimney Cleaning?
Trust in this trade is earned by knowing the product, and DuraFlex liners reward someone who has handled them. Our technicians have up to 13 years of experience with flexible stainless liner systems, and that experience shows in the details: which rotary brush head suits a smooth-wall liner, how much tension a joint can take before it compresses, and when a top termination is the real source of a draft complaint.
We take warranty-safe practices seriously. That means we don’t force components that don’t fit, we don’t cut corners on insulation wrap, and we don’t recommend a full replacement when a connection or accessory is the only thing that failed. When we do replace a part, we source quality components that fit DuraFlex equipment and meet or exceed the original specification. Where OEM DuraFlex components are available, we use them for a precise fit and to keep your warranty continuity intact.
We also work with HeatShield resurfacing and Gelco caps, so a DuraFlex chimney that needs more than a sweep doesn’t send you hunting for a second contractor. Our scope is the full lifecycle: Chimney Sweep, Chimney Inspection, and Chimney Repair, all under one roof. For a Colorado Springs owner with a DuraFlex liner, that means one call can cover the cleaning, the diagnosis, and the fix.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in Colorado Springs
High altitude changes how a liner behaves. At over 6,000 feet, air is thinner, wood burns differently, and creosote builds up faster and in a different pattern than at lower elevations. Add the intense freeze-thaw cycles that work on masonry and crowns, and a DuraFlex liner in Colorado Springs faces conditions that its owner should understand. Here are the problems we see most:
- Creosote packed into the corrugated flutes of a DuraFlex SW (smooth-wall) liner. The flutes are the small channels along the wall of the liner, and creosote settles into them. That buildup narrows the flue, reduces draft, and raises chimney fire risk. In a high-altitude Colorado Springs chimney, this happens faster than many owners expect, so cleaning intervals often need to be shorter than the manufacturer’s generic guidance.
- Liner joint separation or compression at elbows. Flexible liners bend at elbows, and a liner that was undersized or installed with too much tension can separate or compress at those turns. The symptom is smoke leaking into the room or a draft that never seems to pull. It’s one of the reasons we inspect the full run of the liner, not just the firebox.
- Corrosion at the top termination or bottom adapter. Moisture is the enemy of any stainless liner. When a cap or flashing fails, water runs down to the top termination or the bottom adapter and starts corrosion at the joints. Colorado Springs’ freeze-thaw winters and summer hail both put exterior chimney components to the test, and a small flashing failure can turn into a liner problem over a few seasons.
- Insulation wrap degradation or shifting. Insulated liners depend on their wrap to keep heat away from combustibles and hold flue temperature. If the wrap sags, shifts, or breaks down, that thermal protection drops. We check the wrap condition and whether it still sits where it should along the full length of the liner.
- Smoky smell and poor draft that worsen over time. Often a DuraFlex SW liner owner calls after noticing a smoky odor or draft that gets steadily worse. A Level 2 inspection usually finds heavy creosote in the liner’s corrugations, sometimes paired with a failing top cap that lets water in. A qualified local pro would do the inspection, sweep the liner with the appropriate rotary brush, and replace the cap or adapter as needed to restore safe operation.
DuraFlex Parts & Our Repair-vs-Replace Approach
Parts matter, and so does honesty about what a liner actually needs. We source OEM DuraFlex components when they’re available, for a precise fit and warranty continuity. When OEM supply is limited or the cost stops making sense, we use high-quality aftermarket parts that meet or exceed the original specification. We don’t claim to stock genuine parts, and we won’t tell you a component is original when it isn’t.
Our repair-or-replace rule is simple. If the liner’s structural integrity is intact and only the accessory or connection has failed, we repair. That covers caps, adapters, flashing, and joints that have moved. Replacement is the right call when corrosion, joint failure, or widespread creosote glazing has compromised the entire system. Glazing is a hardened, shiny form of creosote that won’t brush away, and once it spreads, the liner can’t be trusted to vent safely.
We’ll show you what we see before we recommend either path. A camera inspection and photo report come with the inspection, so the decision rests on evidence you can look at. Call (844) 560-6330 to set up a DuraFlex evaluation in Colorado Springs.
Our DuraFlex Service Process – Step by Step
We run every DuraFlex job the same way, so you know what to expect.
- 1
Diagnosis. We start with a Level 2 inspection, which means a camera look at the full length of the liner, the joints, the insulation wrap, and the top termination. We’re assessing structural integrity and venting performance, not just glancing down the flue.
- 2
Cleaning or repair. If the liner needs cleaning, we sweep it with a rotary brush suited to its wall type and clear the corrugations where creosote traps. If a joint, cap, adapter, or wrap is the problem, we repair or replace it here, with quality parts that fit DuraFlex equipment.
- 3
Install. When replacement is needed, we install a flexible stainless liner with the right sizing and tension so joints hold and elbows don’t compress. Insulation wrap goes on properly and stays put.
- 4
Test. We check draft after the work, confirm the cap and flashing are sealed, and show you the before-and-after photo record.
- 5
Warranty. We document what was done and how it was done, so your DuraFlex warranty position stays clear and defensible.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Colorado Springs
We service and install the kinds of DuraFlex products that come up in Colorado Springs homes, both masonry fireplaces and factory-built systems.
- DuraFlex SW (smooth-wall) stainless liner kits. The smooth-wall liner is common in wood-burning applications. Its wall is smoother than a corrugated liner, but creosote still collects in the flutes, so it needs cleaning at altitude-appropriate intervals.
- DuraFlex LD (light-duty) aluminum liner. A light-duty aluminum liner is used for certain venting applications. Aluminum behaves differently from stainless under heat and moisture, so cleaning tools and inspection points are matched to it.
- DuraFlex Pro flexible stainless liner. This is a flexible stainless liner for the runs where a rigid liner won’t go. We inspect and clean it the same careful way.
- DuraFlex insulation wrap and mesh kits. These keep heat off combustibles. We check that the wrap and mesh sit correctly and haven’t shifted.
We don’t claim to stock these products. We assess what’s there and service or replace it with parts that fit.
We Also Service These Brands
We’re not a single-brand shop. Alongside DuraFlex, we work with HeatShield for chimney resurfacing and flue restoration, and Gelco for chimney caps. HeatShield resurfacing is a repair category most sweep-only operations can’t offer, and it lets us restore a damaged flue rather than patch it. That breadth means a DuraFlex liner found inside a chimney with a failing crown gets both problems handled in one service visit in Colorado Springs.
FAQs – DuraFlex Chimney Cleaning Service in Colorado Springs
No. We are an independent service provider, not a DuraFlex dealer and not authorized, certified, or factory-trained by DuraFlex. Our expertise comes from field experience servicing these liners, and we tell you that plainly so you can judge the work on its own merits.
Yes. We source OEM DuraFlex components when they’re available and use high-quality aftermarket parts that meet or exceed the original specification when OEM supply is limited or cost-prohibitive. We don’t claim to stock genuine parts, and we’ll tell you exactly what goes into your chimney.
Most DuraFlex cleaning and inspection visits finish in a few hours, and a repair or cap replacement usually runs longer depending on what’s found. A full liner replacement is a bigger job, often a day or more. The written estimate tells you what to expect before we start.
We cover DuraFlex SW smooth-wall stainless liner kits, DuraFlex LD light-duty aluminum liners, DuraFlex Pro flexible stainless liners, and DuraFlex insulation wrap and mesh kits. We service and install these in both masonry and factory-built chimney systems throughout Colorado Springs.
Properly done cleaning and repair with quality parts that fit DuraFlex equipment shouldn’t void your warranty, and we document what we do so your position stays clear. We don’t work as an authorized DuraFlex provider, so we can’t speak for the manufacturer. Keep your installation paperwork on hand, and ask us about any warranty concern before we start.
A standard DuraFlex sweep in Colorado Springs is set per job by a free written estimate after we see the liner. Insulated liners, heavy creosote, or a Level 2 inspection can change the scope, and the estimate tells you the price before any work begins. Call (844) 560-6330 for an exact quote. Estimates are free.
Once a year is the usual baseline, but the high altitude here builds creosote faster, and a wood-burning homeowner in Colorado Springs may need more frequent cleaning if they burn often. A Level 2 inspection tells you how much buildup you actually have. Call (844) 560-6330 to book one.
Often, yes. If the liner’s structural integrity is intact and only a joint, cap, adapter, or wrap has failed, we repair it. Replacement is recommended only when corrosion, joint failure, or widespread creosote glazing compromises the whole system. Call (844) 560-6330 and we’ll evaluate which path fits.
Popping or ticking after a fire usually comes from metal expanding and contracting as it cools, or from a joint that has shifted. If the noise is new or paired with a smoky smell, get it inspected. Call (844) 560-6330 to schedule a Level 2 inspection.
A loose cap usually means the flashing or fastening has failed, not that the cap is defective. Colorado Springs’ high winds and freeze-thaw cycles work at exterior components year after year, so we check the seal and fit it flush. Call (844) 560-6330 for a cap inspection and replacement.
A Level 2 inspection is the standard check after a liner installation or before a change in fuel type or appliance. It’s the camera inspection that confirms the full run of the liner, joints, and wrap. Call (844) 560-6330 to book one in Colorado Springs.
Book Your DuraFlex Service in Colorado Springs, CO
Whether your DuraFlex liner needs a cleaning, a cap replacement, or a full evaluation, we’ll diagnose it with a camera inspection and give you a free written estimate before any work begins. Call (844) 560-6330. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Olympus Chimney Sweep.